| 1 |
Water Inlet Error |
IE |
Correct water level (24.6kHz) is not reached within 8 minutes after water is supplied or it does not reach the preset water levelwithin 20 minutes. |
| 2 |
Unblanced Error |
UE |
The load is too small. The appliance is tilted. Laundry is gathered to one side. Non-distributable things are put into the drum. |
| 3 |
Drain Error |
0E |
Water is overflowing. (water level frequency is over 21.3kHz). If FE is displayed, the drainpump will operate to drain the water automatically. |
| 4 |
Overflow Error |
FE |
Water is overflowing. (water level frequency is over 21.3kHz). If FE is displayed, the drainpump will operate to drain the water automatically. |
| 5 |
Pressure Sensor Error |
PE |
The PRESSURE SENSOR ASSEMBLY is out of order. When water level frequency is consistently below 10 kHz or over 30kHz. |
| 6 |
Door Open Error |
dE1, dE2 |
Door not all the way closed. Loose electrical connections at door switch and PWB Assembly. The DOOR SWITCH ASSEMBLY is out of order. |
| 7 |
Heating Error |
tE |
The THERMISTOR is out of order. |
| 8 |
Locked Motor Error |
LE |
The connector (3-pin,male,white) in the MOTOR HARNESS is not connected to the connector(3-pin, female,white) of STATOR ASSEMLY. The electric contact between the connectors (3-pin,male,white) in the MOTOR HARNESS and 4-pin, female, white connector in the MAIN PWB ASSEMBLY is bad or unstable. The MOTOR HARNESS between the STATOR ASSEMBLY and MAIN PWB ASSEMBLY is cut (open circuited). |
| 9 |
EEProm Error |
EE |
EEPROM is out of order. Displayed only when the START/PAUSE button is first pressed in the Load Test Mode. |
| 10 |
Power Failure |
PF |
Machine is working, the power is supplied rapidly. |
| 11 |
Suds Error |
Sud |
If the washing machine detects too many suds, it displays the error code and adds Suds Reducig cycle. This adds about two hours to the cycle time. If too many Suds are detected during spinning, the washing machine stops to help prevent leaking. |
| 12 |
VIBRATION SENSOR ERROR |
uS |
Vibration sensor to break down |
| 13 |
Breakdown Detergent Pump |
Ed1 |
The amount of liquid detergent in the detergent reservoir did not decrease. After putting the detergent into the detergent reservoir, it was lft for a long time and the detergent hardened. |
| 14 |
Open Circuit Pump |
Ed2 |
The amount of liquid detergent in the detergent reservoir did not decrease. |
| 15 |
Breakdown Softener Pump |
Ed3 |
The amount of fabric softener in the softener reservoir did not decrease. After putting the softener into the softer reservoir, it was left for along time and the fabric softener hardened |
| 16 |
Open Circuit Softener Pump |
Ed4 |
The amount of fabric softener in the softener reservoir did not decrease. |
| 17 |
Communication Defeft |
Ed5 |
PCB does not work due to poor communication. |
| 18 |
Drawer Open |
OPn |
Ther washer was operated without completely closing the drawer. The drawer was opened during the washer operation |
| 19 |
Drain Error |
0E |
The load is too small. The appliance is tilted. Laundry is gathered to one side. Non-distributable things are put into the drum. |
| 20 |
Water Inlet Error |
IE |
Correct water level (24.6kHz) is not reached within 8 minutes after water is supplied or it does not reach the preset water levelwithin 20 minut |
| 21 |
Vibration Sensor Error |
v5 |
Occurs when Vibration Sensor Communication is not working. Such as vibration sensor register setup error, removal, etc. |
| 22 |
Wifi Error |
nE |
WiFi Modem is not connected. |
| 23 |
Wifi modem error |
nF |
Wifi Modem Self Check function Error |
| 24 |
Frozen Failure |
FF |
Supply warm water into thr drum and unfreeze drain hose and drain pump. Wet a towel in warm and apply to supply hose |
| 25 |
Vibration Sensor Error |
vS |
Malfunction of vibration sensor. Replace the Vibraton Sensor. |
