The LG 4681EA2001T Washing Machine Drain Pump & Motor Assembly is your ultimate solution for efficient water expulsion in your washing machine. This high-quality drain pump and motor assembly work together seamlessly to ensure that water is effectively removed, leaving your clothes fresh and clean.
Designed specifically for your washer, this drain pump is activated after the spin cycle speed has been maintained for a specific period of time. It swiftly expels water, allowing you to move on with your day without any hassle. Forget about standing water or damp clothes - this drain pump will ensure that every drop is eliminated, leaving your laundry ready for drying or ironing.
Installing the LG 4681EA2001T Drain Pump & Motor Assembly is a breeze. With just a few simple tools – a Phillips screwdriver, a small flat-blade screwdriver, a pair of needle-nose pliers, and a pair of slip-joint pliers – you'll have it up and running in no time. Please note that the pump casing is not included.
Though this repair may seem daunting at first, it's easier than you think. Start by disconnecting the power and removing the top of the washer by taking out the four back screws and two small brackets. From there, remove the front panel by unscrewing the two screws and releasing eight tabs from the top. As you move down the front of the washer, take out the door, latch, tub gasket, and drain cover. Disconnect the drain hoses and clip from under the drain assembly before installing the new assembly. Finally, reassemble all parts in reverse order.
LG 4681EA2001T Drain Pump & Motor Installation Instructions
Safety First: Unplug the appliance, turn off the water supply, work in a dry area, and have towels/pans ready to catch any residual water.
1. Prepare & Access the Pump Assembly
-
Move the Washer: Pull the unit away from the wall to access the back and underside.
-
Remove Panels: Depending on your model, remove the top or front panel. You may also need to remove the door, latch assembly, tub gasket, and drainer cover to expose the pump area.
2. Disconnect the Existing Pump
-
Drain Hoses: Locate and carefully remove the drain hoses. Detach the hose clamps and remove the hoses.
-
Electrical Connections: Unplug the wiring harness from the pump motor. Label the connectors if necessary for proper reassembly.
-
Remove Mounting Fasteners: Identify and remove the screws or clips that secure the pump assembly. Gently pull out the old pump & motor assembly, noting the orientation of the pump and the impeller for later reference.
3. Install the New Pump & Motor Assembly
-
Compare Parts: Verify that the new LG 4681EA2001T unit matches the removed pump.
-
Mount the New Assembly: Position the new pump in the same orientation as the original. Secure it with the original screws or clips.
-
Reconnect Electrical Wiring: Reattach the wiring harness to the pump motor ensuring proper connections.
-
Reconnect Drain Hoses: Reinstall the drain hoses onto the pump’s inlet/outlet and secure them with the hose clamps.
4. Reassemble & Test the Washer
-
Reassemble Panels: Replace the drainer cover, door, and any panels that were removed.
-
Secure All Components: Ensure all screws and connections are tight.
-
Testing: Plug the washing machine back in, turn on the water supply, and run a short drain/spin cycle. Confirm that the pump operates correctly, check for leaks, and listen for any unusual noises.
Final Tips
-
Drain Hose Maintenance: Consider cleaning or flushing out the drain hose to prevent future clogs.
-
Protective Cover: If the new pump’s design leaves any bare metal exposed, verify whether a cover is needed to protect against corrosion.
-
Consult the Manual: Refer to your LG washer’s service manual for model-specific instructions or troubleshooting.
By following these steps, you should successfully install your new LG 4681EA2001T Drain Pump & Motor assembly. If issues arise or you’re unsure about any step, consult a professional technician.
