Home
|
Error-codes

LG Dryer Error Codes

LG dryers are built for reliable and efficient performance, but error codes may occasionally appear due to operational issues. Identifying these codes can help you troubleshoot and resolve problems quickly. In some cases, replacing essential LG Dryer Parts may be necessary to restore peak performance. Below is a detailed guide to common LG dryer error codes, their potential causes, and effective solutions.

Error Code	Causes & Solutions
Humidity Sensor Failure	Issue:- The humidity sensor is malfunctioning. Possible Causes & Solutions: Load is too small – Try adding more laundry. Appliance is tilted – Ensure the dryer is on a level surface. Laundry is gathered to one side – Redistribute clothes evenly. Non-distributable items in the drum – Remove hard or heavy objects.
Power Supply Issue	Issue:- The electric dryer power cord is not connected correctly or the house power supply is incorrect. Possible Causes & Solutions: Ensure the dryer is plugged into a proper power outlet. Ensure the dryer is plugged into a proper power outlet. Ensure the dryer is plugged into a proper power outlet.
Blocked Vent	Issue:- The duct is 90%-95% blocked. Possible Causes & Solutions: Clean the lint filter and exhaust vent. Ensure there are no obstructions in the vent system.
Door Switch Error	Issue:- The dryer door is not properly closed. Possible Causes & Solutions: Ensure the door is fully closed. Check for obstructions around the door latch. Replace a faulty door switch if needed.
Wiring Connection Issue	Issue:- The motor harness wiring is not connected properly. Possible Causes & Solutions: Check if the (3-pin, male, white) connector is properly connected to the (3-pin, female, white) connector of the stator assembly. Inspect for any damaged wires and replace them if necessary.
Steam Generator Thermistor Error	Issue:- The thermistor of the steam generator is malfunctioning. Possible Causes & Solutions: Restart the dryer and see if the error clears. If the issue persists, replace the thermistor.
EE PROM Error	Issue:- EEPROM operation is abnormal. Possible Causes & Solutions: Unplug the dryer for 10 minutes and restart. If the issue remains, a technician may need to replace the EEPROM.
Water Supply Pump Issue	Issue:- The washing machine detects too many suds and adds a suds reduction cycle. Possible Causes & Solutions: Use the correct amount of detergent. Run an empty rinse cycle to remove excess suds.
Steam Generator Issue	Issue:- The vibration sensor is malfunctioning. Possible Causes & Solutions: Restart the dryer and check if the error clears. If the problem continues, a sensor replacement may be required.
Drum Outlet Thermistor Open/Short	Issue:- The thermistor is faulty or not functioning properly. Possible Causes & Solutions: Check wiring connections to the thermistor. Replace the thermistor if necessary.
Compressor Discharge Pipe Thermistor Open/Short	Issue:- Thermistor issue detected in the compressor discharge pipe. Possible Causes & Solutions: Inspect wiring and connections. Replace the thermistor if defective.
Restricted Motor Error	Issue:- The motor is not starting or operating properly. Possible Causes & Solutions: Ensure the drum is not overloaded. Check for obstructions in the motor area. Restart the dryer after unplugging it for a few minutes.
Low Electric Current Detection	Issue:- The dryer is detecting low electric current. Possible Causes & Solutions: Verify that the power supply is stable. Ensure the wiring and connections are secure. If the issue persists, consult an electrician.
Drainage Pump Issue	Issue:- The drainage pump is not functioning correctly. Possible Causes & Solutions: Ensure the drainage hose is not kinked or blocked. Inspect for any clogs in the pump filter. Contact a technician if necessary.
Compressor Restart Failure	Issue:- The compressor fails to restart after shutting down. Possible Causes & Solutions: Check the appliance for level balance. Ensure that the dryer is not overloaded. Restart the dryer and see if the error clears.
WiFi Registration Issue	Issue:- The WiFi product is not registered. Possible Causes & Solutions: Ensure the dryer is connected to a stable WiFi network. Re-register the product in the LG app.
Vibration Sensor Error	Issue:- The vibration sensor is not functioning properly. Possible Causes & Solutions: Check for loose or disconnected wiring. Reset the dryer and test for functionality.