Product Information
Ensure consistent cooling performance and precision temperature regulation with the LG EBG61106524 Air Conditioner NTC Thermistor. This Negative Temperature Coefficient (NTC) sensor is a critical component of your unit's diagnostic system, responsible for monitoring thermal changes at the evaporator coil or air intake. By providing real-time resistance feedback to the main control board, it allows the system to manage compressor cycles effectively, prevent the indoor coils from icing over, and maintain your specific comfort settings. If your air conditioner is displaying error codes like CH01 or CH02, failing to reach the set temperature, or short-cycling, this genuine replacement part is essential.
The EBG61106524 features a high-sensitivity thermal resistor protected by a specialized moisture-resistant coating. This robust encapsulation ensures the sensor remains accurate even when exposed to constant condensation and the extreme temperature fluctuations typical of an active cooling cycle.
Installation / Replacement Instructions:- Safety First: Turn off the air conditioner and completely disconnect it from the power source (unplug it or switch off the dedicated circuit breaker).
- Access the Sensor: Open the front intake grille and remove the air filters. The thermistor bulb is usually found clipped to the copper fins of the evaporator coil or positioned in the return air stream.
- Trace the Wiring: Follow the sensor wire back to the electrical control box where it connects to the main PCB.
- Disconnect the Old Part: Open the control box cover and carefully unplug the EBG61106524 connector from the PCB. Note the wire routing to ensure the new part is not pinched during reassembly.
- Install the New Thermistor: Plug the new sensor connector into the dedicated port on the PCB. Route the lead wire along the original path and snap the sensor bulb securely into its designated mounting clip.
- Reassemble and Test: Replace the control box cover, filters, and front grille. Restore power and verify that the unit accurately detects and responds to temperature changes.
- AC Temperature Sensor (NTC) – Part Number: EBG61106524
- Precise Thermal Feedback: Provides the accurate data needed for consistent and efficient cooling.
- Resolves Diagnostic Faults: Fixes common error codes related to sensor failure or "open/short" circuits.
- Moisture-Resistant Design: Built to withstand high-humidity environments and prevent signal drift.
- Plug-and-Play Installation: Includes a factory-standard connector for a secure, tool-free electrical connection.
- OEM-Quality Part: A genuine LG replacement component calibrated to match the original factory resistance-temperature curves.
Bought Together
The LG Air Conditioner NTC Thermistor - EBG61106524 is the correct replacement for the following model numbers.
Ensure consistent cooling performance and precision temperature regulation with the LG EBG61106524 Air Conditioner NTC Thermistor. This Negative Temperature Coefficient (NTC) sensor is a critical component of your unit's diagnostic system, responsible for monitoring thermal changes at the evaporator coil or air intake. By providing real-time resistance feedback to the main control board, it allows the system to manage compressor cycles effectively, prevent the indoor coils from icing over, and maintain your specific comfort settings. If your air conditioner is displaying error codes like CH01 or CH02, failing to reach the set temperature, or short-cycling, this genuine replacement part is essential.
The EBG61106524 features a high-sensitivity thermal resistor protected by a specialized moisture-resistant coating. This robust encapsulation ensures the sensor remains accurate even when exposed to constant condensation and the extreme temperature fluctuations typical of an active cooling cycle.
Installation / Replacement Instructions:- Safety First: Turn off the air conditioner and completely disconnect it from the power source (unplug it or switch off the dedicated circuit breaker).
- Access the Sensor: Open the front intake grille and remove the air filters. The thermistor bulb is usually found clipped to the copper fins of the evaporator coil or positioned in the return air stream.
- Trace the Wiring: Follow the sensor wire back to the electrical control box where it connects to the main PCB.
- Disconnect the Old Part: Open the control box cover and carefully unplug the EBG61106524 connector from the PCB. Note the wire routing to ensure the new part is not pinched during reassembly.
- Install the New Thermistor: Plug the new sensor connector into the dedicated port on the PCB. Route the lead wire along the original path and snap the sensor bulb securely into its designated mounting clip.
- Reassemble and Test: Replace the control box cover, filters, and front grille. Restore power and verify that the unit accurately detects and responds to temperature changes.
- AC Temperature Sensor (NTC) – Part Number: EBG61106524
- Precise Thermal Feedback: Provides the accurate data needed for consistent and efficient cooling.
- Resolves Diagnostic Faults: Fixes common error codes related to sensor failure or "open/short" circuits.
- Moisture-Resistant Design: Built to withstand high-humidity environments and prevent signal drift.
- Plug-and-Play Installation: Includes a factory-standard connector for a secure, tool-free electrical connection.
- OEM-Quality Part: A genuine LG replacement component calibrated to match the original factory resistance-temperature curves.
100% Genuine Part
Completely authentic component.
Fast Shipping
Most orders ship out same day
Multi Payment Methods
Pay in many different ways
Full Customer Support
We are providing 24/7 customer support
Wishlist
You currently have 0 items in your Wishlist
